Winter sports fans who have already choose a board for the conquest of the mountain peaks, must be guided in how to properly install the mount on a snowboard.The presence of such knowledge would allow the board to adjust, based on personal preferences and the chosen style of skiing.
structure on a snowboard bindings
Standard mount for snowboarding includes the following set of elements:
- base;
- highback;
- gas pedal;
- strep upper and lower;
- wheels.
Since clip fasteners are always looking out in practice is quite easy to distinguish between left and right mounting snowboard.Just look at the disk on which are marked in degrees from 0 in either direction.The presence of additional openings in the disc due to the need for adjusting the fasteners in the front and in the opposite direction.
How to install the mount on a snowboard, based on the rack?
When installing fixtures matter which foot forward prefers to stand on the board rider during the journey.Snowboarders quite difficult immediately to choose a suitable rack.Basically everything is learned in practice.
However, there is still an effective way to determine the most convenient rack at home.To do this, you must get a little push in the back.What comes out ahead of the first leg, that, most likely, is a leading in the snowboarding.To make sure the result is worth several times to repeat the experience.
If the right leg was in front, then you must install the mount on a snowboard designed for this leg, close to the nose of the board.Based on the nature of the placement host attachment will subsequently adjust the width of the rack.One riders comfortable wide rack, other - narrow.Snowboarders recommended to set the width of an average rack.
Setting mounts
Before we proceed directly to the installation of fixtures, you need to try them together with shoes.This setting is required for the gas pedal.Regulated by this element from the base.To understand this issue, it is necessary to put the boot in fixing, buttoned lower and upper Strep.The gas pedal should be placed in such a position that it reached a bend on the sole of the sock.
How to install the mount on a snowboard?It is necessary to center the Strep.For this purpose, there are special means for adjusting the rear side of the clip.Additionally, you need to pay attention to the fact that the highback tightly resorted to boot.
How to install mounting on a snowboard with a high level of rigidity?
If the available hard board with the appropriate type of shoes, in this case it is better to make the installation of fasteners according to the so-called carving rack that provides an opportunity to steep, sharp turns at high speed ranges.
Angles accommodation on hard snowboard bindings are determined by the width of the board.You should first install the rear mounting so that the socks were looking for a little board.At the same time, the heel should be placed well above the heel edge.This will allow for maximum pressure on the edges of the board.
Position Front attachment should be carried out at an angle of rear mounting, adding to his position about 8o.Subsequently, it will be possible to adjust the corners for a comfortable ride, based on the individual's wishes.
Installation mounts for standard board with soft boots
How to install the mount on the standard model of snowboarding?Try the next, starting with the installation of the default settings for these types of boards that require adjustment of bindings according to the corners + 21 ° / + 6 °.In determining the most suitable rack in practice it will be possible to change the settings several angles about 3-4o in the required direction.
alignment rack
To understand how to properly install the mount on a snowboard, you must deal with the question of alignment rack.It is required to align the feet with respect to the width of the snowboard, which contributes to the stabilization of turns while driving.
best way to center the rack - shod boots with bindings, and then try to feel where you want the foot with respect to the mounting discs.This installation mounting snowboard for a beginner it may be more difficult, as some fasteners have a fixed heel.In other models heel bindings can move in both directions, which contributes to more convenient repositioning of the boot.
stance width
By setting the width of the rack should be understood the distance between the centers of the individual fixtures.To understand how to properly install the mount on a snowboard, in this case, you must start from the parameters of its own growth.
stance width must exactly equal to the distance from the ground to the middle of the kneecap or the rider to be 2.5 cm more than the width of his shoulders.Parameter rack width substantially affects the ability to control the behavior of the board.The most wide-hour imparts stability of the movement, however, complicate the change of edge.The opposite effect is felt in the reduction of the width of the index counter.
Understand how to properly install the mount on a snowboard, based on the width of the rack, it is important for freestylers, who often deliberately increase the figure to perform complex tricks.While fans often prefer downhill narrow rack.
Novice riders is recommended to use the natural rack, resorting to the defaults listed above.Unauthorized modification of this parameter is as advisable only for experienced snowboarders who are able in practice to distinguish between the effect of the adjustment of individual settings.
