In cases where the computer does not have enough RAM, use the paging file Windows 7. Where is this file you will learn by reading the article.In addition, following the advice of experienced users, you can determine the optimal size of the swap file is required for correct operation of the OS.
In some cases, this file is generally not recommended, as it will affect the speed of your computer.Therefore, the paging file is sometimes cut off.But about all in order.
What is the swap file?
There are situations where RAM (physical memory) is not enough.For example, you want to install a game that requires 4 GB of "RAM", but your computer has only 3 GB.In this case, the operating system uses virtual memory, that is, the swap file (the PC).
should be noted that today the cost of RAM is not very high, so it is best to purchase and install several strips of physical memory, as is the virtual hard disk space and takes longer to read it.
As a result, your computer will "slow down."In addition, as a result of these loads the life of the HDD or SDD reduced.
However, if properly set up the OP, it will not increase, "eating" free space on the hard disk to the same hard disk fragmentation is significantly reduced.
way, the paging file in Windows XP7 can throw the disc C (system) to another drive, although some users do not advise to do it.
Where is the swap file?
It is located in a section of the hard drive is called pagefile.sys.This is a hidden file, so if you want to see it, you will need to activate the visibility of hidden files and folders.
Click "Start" and open the PU.Go to "Folder Options" and then on the tab "View".Scroll down and set the slider checkbox opposite the function "Show hidden files".Now click "Apply".
Now you can find the swap file Windows 7. Where is he, you know (the system disk partition).But with him directly produce any action fail.However, there is another method.
deactivate the swap file
If your computer has enough "RAM", then most likely, you will want to disable the paging file in Windows 7. To do this, you will need to click RMB on the icon "My Computer" and select in the context menu"Properties".There is another way - "Start" menu, then enter the CP and open the section "System".
left is a menu where needed "Advanced system settings."Here you are interested in the tab "Advanced", subsection "Performance".Click "Options" and then select "Advanced".Click "Change" in the dialog box, remove the check box next to the option to automatically select the paging file.Select the option "No paging file" and confirm the settings by clicking "OK".Restart the OS.
So you know where Windows 7 to be the swap file and how to disable it.
Setting the swap file
run correctly laptop or computer you will need to properly configure the swap file.First of all, you need to know how much space to allocate to the swap file Windows 7. Where is it, you will remember, so will be able to change its value.Again, open the "Virtual Memory" and then click "Specify the size."
Note: The maximum amount of the EP should be approximately 2 times the amount of "RAM".Original size is better to put the same as the maximum.Alternatively, enter a value that is specified against the item "recommended."
Another important point - the transfer of the swap file from the disk on which you installed the operating system on a different hard drive, which will increase performance.
Now that you know what is a swap file Windows 7 configuration and optimization should not cause difficulties.
Useful tips
heed the recommendations of experienced users, you can properly configure the swap file.Here are the top tips:
- mentioned above, it is better when the virtual memory does not take up space on the system hard drive, since it is already loaded.Ideal - a separate hard drive.
- If possible, install additional RAM strips that do not use virtual memory.As a result, increase the speed of the OS.For "Seven" is sufficient 6 GB of physical memory that is not strongly shake your financial situation.
- Ask your swap file size, because the system it is constantly increasing.This is the reason for the fragmentation of the hard drive.It is recommended to set the same value for the maximum and the starting amount of virtual memory.
way, the minimum size of the FP should not be less than 1 GB in order to prevent fragmentation of the HDD.
Conclusion So now you understand why you need a paging file of Windows 7, where it is located and how to configure it.Of course, it would be better not to use a swap file, especially now that the physical memory is not so expensive.However, if you have an older computer that has no additional slots for RAM strips, the use of the paging file in most cases - the need, as modern games and programs use a lot of "RAM".
As for optimization, you will be able to perform all the settings, following the recommendations of experienced people.It is not too difficult, so you have no problems arise.Talking to experienced users, ask questions, and you are sure to get the answers.
