Before you install plastic door, it is necessary not only to select the manufacturer carefully, but also to pay attention to her accessories.Only in these cases, the door will serve you for decades.But some time after the installation of the door mechanisms may fail.To resolve this problem does not necessarily refer to the masters.Establish mechanisms can be independently.You need to know how to adjust the front plastic door with his hands.
most common causes of breakdowns
As a rule, all the faults of plastic doors arise from violations of the provisions of the canvas.Because of his frequent use of all moving mechanisms gradually fail.Therefore, before you adjust the plastic door, let's first understand, in some cases it is necessary to do so.
- bottom of the door rubs against the threshold.This usually occurs because of inadequate mechanisms strongly clamped.This is explained not by the quality of the door, and inattention master who installed it.In addition, the door skin may sag under its own weight.This is mainly due to the weighted triple-pane windows.
- middle part of the door (near the handle) rubs against the plastic Lutkov.This usually occurs as a result of sudden changes in temperature.
- The door is not closed tightly.The cause of such a failure can be not only the same sudden changes in temperature, and displacement of the pressing roller after a long use of the door.
Preventing problems in the plastic doors
Many people probably think that knowing how to handle the plastic door, it is not necessary to treat it with care.But, unfortunately, it is not.Door adjustment can be made several times.But after a time will come when this procedure is simply not going to help.Thus, you should always remember that the door to prevention should be treated as seriously as their choice or installation.
So, before you buy a particular model of doors, never give up its equipment, even if this would increase the cost of your purchase.Otherwise, before you adjust the loop plastic doors yourself, you will need to again spend time and money trying to find a particular kit.
tools required for plastic doors
most important tools for adjustment of plastic doors is considered to be the following:
- microlift.This tool will help troubleshoot any size and weight of doors.It helps prevent sagging even the heaviest door panels.Lifter takes over part of the cargo door, but only in its closed position.It may look different.The most common types of it - is at the bottom of the video clip or a movable plate at the top of the canvas.
- Limiter door opening.This mechanism is not only helps prevent sagging of the door, and sets the maximum angle of opening thereof so that protects the blade from hitting the slopes.
Also, before you stop for choosing a producer of plastic doors, find out more information.The fact that many companies are neglected quality of the fitting, mounted cheaper, which may also be one of the reasons for the minimum period of use.
slack leaf
We have already seen what determines the sagging canvas, now let's look at how to correctly adjust the plastic door with his hands in this situation.
If you notice that the fabric clings to the threshold, you need as quickly as possible to eliminate this problem.To do this, open the door and find a small loop at the top of the screw.As a rule, it is a hexagon.In some cases, it may take the form of an asterisk.In a particular case, you will need to pick up the key to the screw.
So, turn the screw clockwise.Make two or three turns.Cover the door.Now she must be free to close.
If the fabric is very slack, and these steps do not resolve the fault, the experts suggest the following as the plastic door handle height.Locate the adjustment screw under the protective cover of the lower canopy and rotate it a few times in a clockwise direction.These actions will help you resolve the problem with sagging door.
Remedy mashing leaf side
Wipe the side door is also easy to prevent.How to adjust the plastic door in this case?For this, find the lower canopy has now another screw that is not from below but from the side, i.e. the inner side of the web.Again, again, spinning clockwise, you can put the door leaf to the desired location.It will no longer cling to the doorjamb and could easily be closed.
If this method did not resolve rubbing the side door, get the upper canopy, about which was written above, and follow the same steps.
Establishment of tightness of doors
If you notice that your door is locked is not tight, this item troubleshooting - for you.Let us consider how to adjust the clamp plastic door.
to start taking pictures look on the ends of the door.There are special cams.Their rotation is possible to establish the correct mode of the door.The only problem here - to find the right eccentrics.Usually at the top, side and bottom set of threes.All they have to be gradually turned at the same angle so that the door closes.But since it will fit only near the handle, you must still be adjusted canopies special screws.
Adjust door handle
We have already discussed how to adjust the plastic door.But what if it is not functioning properly handle when opening?Do not worry, eliminate such problems, you can also handle with their hands.
To do this, move the decorative plate 90 degrees.Underneath you'll find a mechanism handles and screws.Screw these screws and the handle on the door leaf will be fixed strongly.Thus, you are able to adjust its density lock, which makes it possible to eliminate the problem of the door opening mechanism is tight.
Replacing door handles in plastic
Now you know how to adjust the plastic door with his hands.But most of the difficulties it would cause a replacement pen.After all this hardware is the most vulnerable.It should also be noted that the term of its operation is much less than that specified by the manufacturer.
main cause breakage of plastic door handle - is the poor quality of the material.Constant foresees its use in cracks, and in the future - to ensure that the handle broken off completely.
If you are faced with the latest problem to begin to pick up your analogue knobs.Choosing one or the other accessories must be carefully, paying particular attention to the identity of the size of the parts and fasteners.As a rule, all these devices are almost identical, but to be safe in this case is superfluous.
Mounting handle is done directly to the metal hidden under the plastic base profile with screws, which subsequently closed decorative caps.
We hope these tips have helped.Now that you know how to adjust the front plastic door yourself.
