use of television receivers in some cases may require installing them emulators that are adapted to run coded channels.Among the most popular solutions of this type - MGCamd.Installation and configuration of the emulator can be accompanied by a number of nuances.What should I look for when working with MGCamd first?
Specificity emulator
include emulators, well adapted to the overview encoded broadcasts via cardsharing - MGCamd 1.35.Setting this decision properly allows you to run the appropriate channels with the activation of the keys, which are registered in the file structure SoftCam.Key.
Setting emulator
investigate how the emulator is set to spread receivers such as GI 8120. Before the decision of the respective task, you must make sure that the receiver has been deactivated compatibility option c encoding Conax.It is necessary, therefore, enter into the management interface devaysom, select "System", then - "Basic Settings", and then - "Conditional Access".It should then make sure that the front of the item Conax is checked "Off".If it does not - to put it.
next task - installation of the emulator in question, as well as its configuration files to the receiver.To do this, you must find the appropriate archive folder MGCamd Plugin.You must unzip it into the root area of the stick - in this case it must be formatted in the FAT32 (this can be done through the Windows).This will insert a USB flash drive into USB-port of the receiver of this type.It is important that at this point the device was turned off.After it is turned on and booted, the software interface prompts the user to install the plugin.You must use the remote control to confirm the agreement on the installation of the respective component.Then start the installation of the emulator.Upon completion of this process, the receiver will restart.
After switching on the device may again request the installation of plug-in, but this time it is necessary to abandon the procedure and wait for further loading device.After that, the remote must be selected, designed to safely remove the stick, and then - turn off the USB-device.
Setting emulator
How is setting MGCamd?The solution to this problem is carried out in several stages.
first thing to do, using the FTP-client, enter the settings on the receiver.For this need to enter a username and password - in both cases, this root.You should check the file mg_cfg and make sure that there are the following options:
- G: {01};
- B: {01}.
If the values are different, then it may be difficult to view channels via cardsharing in several modes.
Setting Cardsharing
next task - setting Cardsharing emulator MGCamd.To do this, connect the receiver to the Internet.Also need the correct option from the server cardsharing to enhance the desired packages.
basic protocol by which the setting MGCamd at this stage - Newcamd.For his engagement necessary to make changes to the parameters contained in the file newcamd.list, located in the file system of the receiver.As an editor, it is desirable to use the program, adapted to work with the Linux-files.Among those - UltraEdit, and you can use it.
consider in detail the structure of the file newcamd.list.It contains a few lines.Some of them will be used by us in the course of solving this problem, as configuring MGCamd.
string CWS_KEEPALIVE
Among those - line CWS_KEEPALIVE.It fixed time after which the emulator checks the connection to the server cardsharing in accordance with the configuration of ports.The corresponding option can be disabled when it comes to using NAT-router, deactivate idle connections.Another option to use it - start coded channels immediately after the transition from open broadcast.
line CWS
stitch CWS, in turn, it is extremely important for us when dealing with MGCamd.Setting sharinga it requires making necessary adjustments.There are fixed parameters for cardsharing server that needs to run some or other packages.So, instead of the phrase IP Server must lock the domain name server cardsharing, and even better - its IP-address.Instead, Server Port should enter the port to a specific channel package.Personal login and password change accordingly - write there login and password.After that, you must specify DES-key.It will look like a series of numbers from 01 to 14 (between the digits - spaces).
close to the above lines in this file is the other - CWS_INCOMING_PORT.It fixed port used with the purpose of listening to incoming packets.In practice, these settings are almost no need to adjust, so you can not ignore them.
work with other files
Setting MGCamd also involves working with some additional files.Among those:
- priority.list;
- ignore.list;
- replace.list.
They are located in the file system of the receiver.Their mission - to accelerate the process of launching the encoded channels if they have a large number Ident.But if you use a local surfer Cardsharing, the relevant files usually include the correct settings that change is needed.Edit they need only if the supposed involvement of other servers Cardsharing, or in the case of changes to the current options.
agree that the need to work with these files we are still there.
configuration file priority.list
When it comes to file priority.list - it is operated to lock Ident, through which channels should be run.
denotes they can form double digits.Userid in fixed lines through letters and braces.For example, V denotes the encoding that is activated when the broadcast channels, namely - Viaccess.Ident tend to fix the desired resolution television images - eg, SD, or HD.
Enabling encoding files must be carried out according to certain rules.Consider some examples of specifying their values in the required file priority.list.
For example, when it comes to encoding type DRE-Crypt, the file needs to be written line X: {4a e1}.The letter X indicates that the marked encoding is activated.Meaning 4a e1 - it CAID.
Another common encoding - Irdeto.If it is activated, the file needs to be written line I: {00 01}.Similarly, the letter I - is marked by encoding the numbers 00 01 - is CHID.
If encoding is used Seca, the file you need to register a string S: {00 84}.In this case, the letter S - a designation specified encoding, and 00 of 84 - this ident.
If you use the coding NDS, in the file you need to register a string X: {09 0F}, where X - is the designation coding NDS, and a value of 09 0F - it CAID.
When you enable the encoding Nagravision file should set the line X: {} 18 October, in which the X - as encoding, 1810 - CAID.
configuration files and ignore.list replase.list
Next file - ignore.list, includes the username, which should not be used when running channels.
third image of said - replace.list, is activated if you want to replace invalid userid to those that are functional.This may indicate additional options for channels.Most often used in HD-broadcasts.
lines in the file looks like this:
R: {{2F4F} {0500} {023700} {0FA6} {0500} {030600} {0BBE}}.
What does this sequence?Meaning {2F4A} - this seed broadcast, {0500} - the encoding Viaccess, {023700} - is replaced ident, {0FA6} - ECM PID.Next come the correction values.That is, {0500} - this is a new encoding {030600} - a new id that replaces the current, {0BBE} - valid ECM PID, the corresponding channel.
also configure the plugin MGCamd may require working with the file mg_cfg, which records the configuration parameters.
After we reviewed the files properly edited - provided that it is required to do because of the specific server - you need to reboot the receiver.Make it the best way:
- you first need to put the device into standby mode by pressing the button on the remote control;
- after this - turn off by a toggle switch, located in the rear of the device.
In turn, the inclusion of the receiver should be carried out in reverse order.When the device is booted, select the menu item "Plugin" and click OK.
Approximately emulator is tuned MGCamd.Of course, this is a very "framework" criteria.In some cases, it requires more detailed editing of files for the correct engagement emulator MGCamd.Fine-tuning the receiver in some cases, moreover, it may require the involvement of qualified specialists in the field of television equipment.
Setting the receiver and connect it to the network
Saved us the problem may be supplemented by the need to adjust the receiver type GI 8120, and connect it to the network.How these actions can be done?
Relevant work with the receiver, also used in solving this problem, as configuring MGCamd - GI 8120, may be needed if:
- the device has just acquired;
- its settings are reset to the factory.
In both cases, you may need to set the correct options "from scratch".
Receiver in question, and with the involvement of which is tuned MGCamd, GI 8120, has a Russian interface.If the Russian language it is not activated, then this should be done by remote control.
Then press the button PAGE +.Then - it is necessary to fix the infusion time.Here, the key will be the following options:
- Auto Update (if you activate it, the time will be synchronized with TV, but you can also enter the desired values manually).
- GMT Offset (with the help of this option you can lock the relative Greenwich time zone).
- Summer Time (if it is activated, the receiver will translate into saving time).
device may also be required to connect to the network.Typically, the receiver itself displays a message that it must be done.To make this connection, you need to connect the device via Ethernet-cable to a router or modem that operates in the router - it should, at the same time already have an active Internet connection.In some cases, the receiver can be connected to a PC via a crossover method, or via Wi-Fi.
To ensure correct interaction of the receiver and the router, you can use the protocol DHCP.This will, in particular, router, define the required network settings automatically.In order to use DHCP, you need to enter the settings of the receiver and put the contrary point DHCP option to ON.
But it may happen that the DHCP-server is not used on the router.In this case you will have to enter the parameters of the local network manually.
After the user completes the network setup, you will need to specify the interface to operate the receiver the correct settings on the video output.In particular, in paragraph TV Standard You can set the resolution of the displayed images.Paragraph Screen ratio - the proportion of the display.In paragraph Conversion - a way to convert images through a particular regime.
configuration settings
receiver may need to work with configuration settings.Among those:
- Message Auto Play (activates the display of messages).
- Software Upgrade Notify (activates the subscription for the software update of the receiver).
- Video Upgrade Notify (provides an opportunity to upgrade the video).
- Audience Rating (enables the assessment of the rating).
- Video Clip Service (allows you to play video system).
complete the configuration, you must press the PAGE +, then the receiver will begin to work normally - in particular, a menu display channels.
variety of solutions
So, we looked at how you work with MGCamd (installation, setup, configuration), and also investigated the basic nuances of setting one of the most common models of receivers, which are compatible with this decision - GI 8120. Of course, those momentsthat we have learned, can be complemented by a large number of other nuances of engagement emulator.Such a need may arise from the use of other versions of the solutions.So, setting MGCamd 1.38 will have their own characteristics.Much depends on the specific device types.For example, if the receiver, which is tuned MGCamd - SkyWay, the nuances of the operation of this device will also require detailed study.
