installation for generating electrical energy.The fuel used for the installation - the air.
All you'll see below, my proposal may seem nonsense or utter nonsense.Maybe.But let's not jump to conclusions.
immediately propose mentally take a tour 20 years ago, in the 90s in Russia.We all still remember those years.Surely we remember and how waited in line to be installed in the apartment landline phone, and if you then said that in the future 20 years from now, landline phone becomes a simple commonplace in your daily life and, moreover, appear cell in which you andradio and television, and all that you want, for many of us, then it would have sounded crazy, it is not clear from the realm of fantasy.In short everything is taken seriously it would not be.Today, however, all of this for us is already a reality in life.It is, for example, that we should not jump to conclusions.
now give another example, which will become more clear.Many of us in childhood, probably had in its arsenal of toy cars with automatic winding, which are not based in the factory key, t. E. Not spring mechanism, not from the batteries and electric motor, and purely mechanical.Pressing the machine to the floor and rolling it across the floor, we thus wound up it, and then let her go, and she was rolling.This was achieved due to the fact that a slow rotation of the wheels of smaller diameter through a certain set of gear spins the wheel of an internal mechanism with a large diameter and with greater speed, and when we let go of the machine, the torque transmitted to the wheels of the machine, causing it and rolled.
This little mental excursion in our childhood was needed in order to show the possibility of converting the torque to a lower frequency of torque with greater frequency.
now turn to the essence of the idea.And her description.For your consideration proposed the idea of a plant that will produce electrical energy, and thus, does not require for its work no petrol, no gas, no oil, no oil, no solar panels, no radioactive elements, no extraneous electrical sources.Completely self-contained, launch and follow-up work.Immediately it should be noted that the installation can be both portable and stationary, both small and great, everything will depend on your needs.The driving force for this is the installation will be just the air, and after working in the system at the exit from it, exhaust air, that with regards to the environment, according to their chemical and physical characteristics will be absolutely identical to the air in his condition prior to entering the system.In principle, the driving force can be any medium which will be used in this setting.The only requirement for your environment will be the absence of the viscosity and discharge.In our case, we consider the air just air.
Now, a little fantasize and visualize any petrol or diesel engine.Mentally, we cut off the piston and remove the system, leaving the crankshaft, and instead put the piston hydraulic diaphragm valve, and their uvyazhem rod to the crankshaft.
Now let's look further.
Below is a diagram of the power plant, where some of its elements are reflected in the form of transfer functions of the units (oscillating, amplifying, and so on. N., Depending on the functional element present in the system), and their relationship and the direction of the impact on each other -arrows.
Brief description of the installation steps:
first transfer function describes the capacity of the air under high pressure HP.Air under high pressure acts on the upper inner cavity hydraulic diaphragm valves, hereinafter MC (these valves are widely used, for example, at power) and thereby acts through the lower cavity and a rod on the crankshaft.Hard feedback crankshaft and MC provided a spring system.This diagram shows a push-pull system "engine", which in the basis of the "piston" taken two MC.Synchronism of operation of two push-pull circuit IC provided in this case by operation of valves of the valve system COP, each of which is embedded at the inlet and outlet of each MC respectively.A valve between the COP MC are both rigid interconnection through electrical and hydraulic signals, which in turn provides the aforementioned synchronization of the MC in push-pull mode, and smooth rotation of the crankshaft.By COP also expected to speed control torque.This "motor" is planned very low speed, which will provide a low air consumption and durability of its individual elements.Since the engine low speed, the rotation of the crankshaft to the generator is transmitted through a specific set of gears that provide an increase in the rotational speed of the generator rotor.From the part of the energy generated by the generator is supposed to work is the compressor, which will compensate for the spent air in WA.Parish air into HP should be greater than its expenditure.Also part of the energy generated by the generator charges the battery, which provides the performance elements of the COP in the initial startup of the entire system.In principle, the initial start-up can be done completely mechanical, without any email program separate sources.current (battery for easy initial launch).Device dimensions will depend on the capacity of the generator, ie. E. If other words, the needs of the consumer.With proper alignment between the COP and an MC and configure them properly requires a high reliability and efficiency in the use of these facilities.
At the moment, the proposal is expressed only an idea, based on the practical and theoretical considerations and reflected the diagram shown above.Design decisions, including any calculations or not.All this will be possible to obtain, starting from the first experimental model created.
purpose of this article - to find like-minded people with the environment and features that allow to realize our plans.Any criticism will be accepted and subject to appropriate analysis.
