Every woman knows that the stove - the most convenient tool, which is in almost every home and you need to prepare any meal.At the same time it's pretty dangerous appliance, because the connection is made to the gas cylinder or gas pipes.How to connect a gas stove in the apartment of their own, known not to everyone, so will be described below, what requirements must be met, and that you may need to install the device and connect it passed without incident.First, you need to work under very strictly follow the instructions included with each plate to follow safety rules.
Organization of space for gas cooker
When you choose the place where, and how to connect a gas stove, you need to take into account mandatory rules of technical safety.Therefore it is necessary to know the following:
- plate should not be placed within four meters of metal pipe pipeline;
- modern gas stoves necessarily have electronic ignition and lighting in the oven, so far from the most modern boards should be socket with earthing;
- as a flexible wiring, you can use different types of hoses: a rubber having a metal braid (considered to be a good option to safely connect the stove), rubber-and-canvas (rather flexible hose, according to it, current flows, but it is hard enough);
- pipes intended for water, marked by blue and red marks, and gas - yellow, so it would be difficult to confuse;
- the toughest hose, but at the same time and is considered to be an expensive bellows metal hose.
Please note: no matter what branch you choose.To install the gas stove was successful, as long as it is equal to the inner diameter of at least 10 mm.This is necessary for a good passage of gas to the oven and all burners.
What do I need to install
- open-end wrench or adjustable to 22, 24, 27.
- Phillips screwdriver.
- Gas number one key.
- Len (but it is better to replace tape FUM).
- gasket having a diameter of 13 mm (most often it is possible to take a complete set of plates).
- sealing thread.
- emulsion of soap solution (which is used to check for gas leaks).
- ball valve by 13 mm.
- gas hose length needed.
How to dismantle an old gas stove
To answer the question "how to connect a gas cooker", you must first decide what to do with the old unit (to install new or replace the old parts).First of all, before you start dismantling old gas stove, you must close the gas valve.Once you have verified that the gas supply is not, you can start loosening the locknut and sgonke standpipe coupling on the gas stove.Oldest plate clutch is quite difficult to remove, because it is often covered with several layers of paint.In this case, it would be appropriate to cut it with the Bulgarians, the rest unscrew.
Then you can push the plate away from the wall to provide access to taps on the back.With the correct wrench gets out eviction from the tap.In the case where a new gas stove plan to put a little later, then put the cover in place eviction.
Installation and connection of a gas stove in the apartment
The apartments mainly produce gas stove connection to the pipe with a central gas supply.
Once dismantled the old technology, you can install a gas stove.In the first place the new device should be released from the packaging container, leaving only the protective film (which is removed after installation).Put aside all the parts that came with the stove (a baking tray, etc.).Next, using the level and leveling feet to level it should be.Between the gas stove and the wall is necessary to keep a little distance.
After the installation of a stove made in place of the hose connections and establish a lining of the plate diameter of 13 mm with a metal mesh.It is necessary that during the operation in the appliance from dirt and debris, which will significantly increase its service life.
This connection is tightened using a spanner size.Using soap solution node is checked for leaks as follows:
- in a small circle or a plate a little thickish diluted soap solution;
- fully open the gas valve, the handle should be parallel to the gas pipe;
- brush or your fingers to smear the place thoroughly hose connection.
Thus it is necessary to look carefully, there appeared on the surface of a soap bubble solution.If there are none - the connection is good, and the gas is not leaking.And if there is - should close the valve again and tighten the mounting assembly.
Features selecting a gas stove for connection to a container
in a private home or cottage is often no central gas pipes.In this case it is possible to connect the gas cylinder to the stove.The use of such equipment in the kitchen will have certain nuances, such as installation plate and its connection.
in bottles usually contain natural gas supplied under pressure of 3.6 kPa.This is the important factor in selecting and adjusting the tap nozzles for installation.Choosing the plate, in which the gas will come from the cylinder, it is important to consider the following points:
- usability;
- the number of burners;
- plate dimensions and its weight;
- jet equipment;
- the presence of additional functions;
- if equipment are adjustable gears, this greatly simplifies the question of how to connect a gas cooker;
- not all gas ranges are designed for connecting to cylinders;
- the individual characteristics of certain plates, which are intended only for a certain type of fuel.
Installation and connection of the gas stove to the cylinder
Self-installation of gas equipment is prohibited.This requires professional help.Since it is because of incorrect connection and use of the gas cylinder case a huge number of accidents.
But not always in rural areas have the necessary experts, however, adhering to the rules, written below, you can learn how to connect a gas cooker:
- according to the rules of fire safety gas stove should be installed at a distance of not less than one and a half meters of gascylinder;
- an ideal option would be, if the installation of the cylinder on the street are equipped with special metal box, which is closed to the castle;
- gas stove must be installed in a well ventilated area;
- if during the operation of the plate you smell gas, immediately shut the gas valve is necessary and open all windows and doors for ventilation;
- periodically check that the hose remains complete and its connection to the stove sealed.
installation drawing Installation drawing
as installing a gas stove, must be carried out only by specialists.But if those are hard to find, you can do it yourself, in accordance with safety regulations.
exhaust must be installed on a gas stove at a height of 650-800 mm.This will provide the necessary security and protection from heat exhaustion.Also, such a height is set based on the fact that until the control panel should be comfortable and easy to reach.
Do not forget about the width of the hood, it must be the same as the stove, or a little more.This will help ensure good circulation over the gas stove.
Basic requirements for installation of the hood
- vent straight up from smaller parts.
- Installation drawing as much as possible try to avoid bending corrugations.
- If you want to change the diameter of the vent, use adapters, which are attached directly to the drawing.
- Inside Breather should have a smooth surface.
Now you know everything you need to, and can easily connect a gas stove yourself and save the family budget.
