foam gun - a tool very useful for any repair or construction.This device is necessary not only to save time, but also more economical use of the foam.Significantly increased and the accuracy of the application, which again leads to cost savings.Let's talk with you about how to use a gun for foam.It is not difficult, but you must follow some rules.
Some general information
installation of plastic windows, door frames, and much more needs bookmark foam.Manually applied it quite problematic for many reasons, but using special equipment can save time and power.Today, sells a variety of guns for applying foam, some of which differ structurally.But we can say that much among themselves differ only in tanks with foam.Nevertheless, most of the more or less high-quality guns fit any bottle produced.Before you use the gun for foam, it is necessary to take care of their own security.It is advisable to wear gloves and goggles, although many manage without it.Also, before you begin, you need a good shake bottle.
device gun foam
Let us briefly consider what elements is this tool.The design of the gun is very simple, and there is no complex assemblies.The nozzle should be 5 times smaller in diameter than the tube.This is to ensure the optimum pressure and the possibility of applying a thin layer of foam.Also has its own handset, it is often called the trunk.Pretty important part - adapter, also known as an adapter.Speaker connector between the gun and the tank with foam.The design provides for the presence of an adjusting screw, which allows you to control the output of the foam.It is advisable to buy a model with the nut barrel to the handle.If you remove it, it will have access to the stock, so clean it can be performed without any problems.There is still the trigger and handle.The last element in the priority should be aluminum and quite durable.As you can see, the device gun foam is simple enough.Let's go further.
On charging gun
The cylinder has a protective cap.Before use, it must be removed, after which the balloon can be screwed into the holder gun.However, you should understand that while working cylinder should be inverted, that is, the holder is at the bottom and an adapter - at the top.Accordingly, the gun is inverted so that the handle faces down.During the wrap with one hand to keep the gun and the second rotary motions to insert the balloon into the holder.To purchase a homogeneous composition of the mixture contained in the vessel, the balloon should be well shaken.Shake it better unturned position, that is, the handle should be at the top of the gun.About 15 will be enough agitation.Well, now you can understand how to use a gun for foam.As noted above, there is nothing complicated.
about packing foam
now would like to consider the general principles of work not only with a pistol, but with the foam, since this stage is quite important.Before starting work, you need to moisten the surface.This is to ensure that the swelling of the foam was faster and better, and the structure was completely homogeneous.The nozzle is directed towards the seam.On the need to press the trigger smoothly and without jerks.So the quality of foam at the outlet will be higher and less risk of breaking of the trigger.The slot must be filled from the bottom up.This nozzle needs to be done as it zigzags.With the adjusting screw to increase or decrease the amount of feed in the trunk of foam.It depends on the depth and thickness of the treated joint.
not forget that in the process of mounting a foam gun with tank must be periodically shaken.If the gap is too deep processed, then use a special adapter that fits on the gun barrel.
Gun Foam: instructions on how to change the bulb
It's pretty easy handling, requires no preparation.Naturally, during operation, the amount of foam in the tank decreases.After the resource has been completely used up, replace with a new bottle.This is done as follows.
barrel of the gun sent to the trash.By pressing the trigger you must remove the remaining foam from the trunk.After that, the gun handle is turned up, and the balloon gets out rotational motions.The anchor should be cleaned with a special liquid and immediately carry out the installation of the new cylinder.How is its installation, we have already dealt with.Now, under the gun assembly foam ready for use.
What to do at the end of work
Once you have finished, you need to stop the adjustment screw.If the container is still a certain amount of foam, and the next use will soon (within 1 month), then perform the removal of the balloon does not make sense.Moreover, it is strongly recommended to leave it in the gun.So the foam is under constant pressure, which prevents it from drying out.Before the end of the tip must be well cleaned with a special liquid.This prevents drying foam, respectively, the next will be much easier to use, since it does not require pre-treatment.If the cylinder is empty, and there is the new, the old is removed and the gun is cleaned.In principle, and the gun is used for the foam.Instruction does not end there, there are still a few important details.
Briefly about cleaning
Many do forget about this procedure, considering it an unnecessary and pointless.But it is somewhat not.The fact is that if the foam hardens around the barrel, then remove it out to be problematic, and it takes a lot of time.That is why immediately after completion of the work necessary to clean the instrument.To this end, the outlet of the barrel is rotated to position "on my own."Thereafter, the balloon gets out with foam and inserted into the holder cleanser.Then you have to press the lever until the barrel is completely filled with cleaning agent.It is necessary to wait for about 10-15 minutes, after which the liquid is removed, and the barrel is repeatedly washed.When the balloon take off with cleaning liquid, press the trigger to remove remaining detergent.Tighten the adjusting screw until it stops.Basically, that's all you can tell us about how to use a gun for foam.Now let's look at the tools from renowned manufacturers.
gun foam Hilti
The company is engaged in manufacturing and sale of professional models.For example, Hilti CF-DS 1 is very popular among professionals and everyday life.This gun will cost 2500 rubles.Instead, you get an ergonomic design, robust products and high quality assembly as a whole.The anatomical handle has a non-slip and lies well in the hand.The hammer is large enough and designed by two fingers, which increases the convenience of work.In addition, the gun foam Hilti CF-DS 1 has a fuse.It blocks the trigger from accidental operation during transportation or drop the tool.The weight of the gun - only 480 grams, so working with him, the operator will not be tired.
Conclusion If you want to buy an inexpensive tool, then pay attention to gun foam "Zubr".That's a pretty high-quality tool, most of the models have a lightweight body, enabling better and more accurate to carry out the work, the hand of the operator will be less tired.In general, the products are made of steel and are quite strong and airtight.Here, in principle, and all you can talk on the subject.If you are looking for the best gun for foam, then give preference to popular manufacturers.It should be understood that there are other good options, cheaper and more accessible.Today, many domestic companies supply good and cheap enough guns foam.How to use them, you know, and the technique will come with experience.
