Setting DIR-615 router from D-Link's not so too difficult task and solve it according to every user, regardless of his level of knowledge.This article will be given a stepwise algorithm for solving this issue, following which, in 15-20 minutes you can easily setup your router.
Specifications network device
This model router refers to the initial segment.Therefore, equipment she is quite modest.The list includes:
- wire twisted pair cable, crimped on both ends of a length of 1 m.
- the router itself.
- power supply to the network device.
- Instruction manual and warranty card.
The network device has 5 ports for a wired connection.One of them - the entrance.It connects the wire from your Internet service provider.The other four are for the creation of the wired LAN.The maximum data rate it is 100M bits / sec.But it should be noted that the speed at the input port will be limited by the ISP.In turn, a wireless computer network part peak rate can reach 300 Mbit / s.The device supports the most common to date standards "wi-fi»: b, g, and, of course, n.
indication and connection
An interesting design of the competition boasts the router.Externally, it is a black box, made in the form of a trapezoid.It is on the side of the trapezoid and displayed dashboard.It consists of the following components:
- Power LED - indicates the presence of voltage.
- Search indicator devices based on technology WPS.It flashes during the search.
- LED transmission of information from the global web.It blinks continuously during exchange.
- following indicator indicates the presence of connection to equipment ISP.If it is flashing or lit, then everything is fine.If we went out, there is no input signal from the upstream router provider.
- Next are 4 LED indicating communication with devices connected to the corresponding wire port.
On the opposite side of the network device removed 5 wired ports, click "reset", "CHD" and "believe."Also here is a jack connector from the power supply.
Settings "Rostelecom»
From connecting the router and make the necessary software is setting the parameters of the router DIR-615."Rostelecom" (these options are on the tab INTERNET), for example, requires setting of parameters:
- Network address - dynamic.
- Connection to the global web - "PPPoE".
- login and password are specified in the contract with the provider.
All other parameters are left without changes and only those associated with the wireless transmission of data, can be set to your liking.
values for users "Beeline»
«L2TP» - this type of connection is required in this case, setting the router DIR-615.Of Beeline in this sense stands out against other providers.The address in this case is obtained from a provider, that is, it, as in the previous situation, dynamic.More specified username and password provided in the contract for the provision of data services.To gain access to local resources need to activate the technology UPnP (this option is set on the tab ADVANCED NETWORK), this is what require in this case, configure the router DIR-615."Beeline" -Connection fully configured and then you are ready to scan.
Configure router under the "TTR»
This provider is much more difficult than in the previous two cases, passes setting DIR-615 router."TTR" jobs require a much larger number of parameters.First we need to create a template in connection with any router name (click "Firewall", the sub "virtual servers").It then select the interface - WAN.Then this template add two types of connections: TCP and UTP.The first of them bind to port 30001, and the second -30,002.Moreover, these addresses are specified as the incoming and outgoing port.Also in the protocol parameters you must specify a static IP address of the personal computer.The router itself is already configured to work with your ISP.But the PC is not.Next, set exactly the same static IP address on a computer, which was introduced in the sections of the router.Then set up a special program Pulse ++ K.It specifies the exact same settings that have been made to the profile of the router.Also cancels dynamic addressing and set a fixed address.You also need to add the program to the exceptions brendmaura.Also in this program is installed check box next to the network "TTR" and select it by default.
«Ufanet»
In this case, in comparison with the "TTR" much easier to configure the router DIR-615."Ufanet" -Connection requires specifying the following settings on the router (tab INTERNET CONNECTION):
- device address - dynamic.
- Connection Russia PPTP (Dual Access).Also specify the gateway address rrtr.ufanet.ru.
- Enter your username and password from the registration card.
- Set check «Reconnect Mode» to position «Auto».
Putting scheme
In the first stage setup router DIR-615 is reduced to the collection scheme.To begin, select the location of your router.Next to it should be fixed socket, which will provide its power supply.Also, this place must be easy to reach the incoming wire from your ISP.Another important recommendation - a router should be as close as possible to the center of your home, office or apartment.This will greatly increase the coverage and get almost anywhere a high level of wireless signal.Also finding is not allowed access from the network device the metal sheets.It will be put out signals and cause interference.A similar problem may arise in the case next to the router will be a microwave or refrigerator.A scheme going as follows:
- Connecting the Router's power supply into a wall outlet and the power cord from it in the appropriate slot on the router.
- Next wire from the provider to set the connector to the port labeled Internet.Similarly connect those network devices that are to communicate via the twisted pair.
software configuration
The next step is configuring the router DIR-615 comes down to making the program parameters (they were previously listed) in the software configuration of the router.To do this, turn on the router and computer.Then wait until the end of the loading of each of them.Then, run any of the install on a PC web browser.In his address bar, enter the address «192.168.0.1 (this is the address of our router in our computer network) and press" Enter. "After that, you will be prompted with the login and password of the router.The first and second fields of this request, enter «admin».If the router is not new and they are someone has already used, these parameters are subject to change.In this case, the entire configuration of the router will have to return to factory settings.It is enough for 20-25 seconds, hold the "reset."Then repeat all over again.
Once Once clicked, the interface settings are making parameters that have been described in detail in the preceding sections.Next, ask your wireless network - its name, password and encryption method (be sure to select WPA2 - it is the most reliable).At the end do not forget to save all.Thereafter, it is recommended to reboot the router.To do this, simply press and release the button "Believe."After that, the router should be switched off.Then you need to take a break - 10-15 seconds.Next, turn on the router, and after loading it is ready for use.
Check the "wi-fi" and a wired connection
This setup WiFi router DIR-615 is finished and only need to check the performance of the wireless and wired LAN.In the first case it is sufficient to run only on a PC browser and enter any address.If you open the home page of the site, then everything is fine and you can start testing the wireless way to transmit information.Otherwise, check the settings made to the router.But on mobile devices testing procedure differs slightly:
- go in the tablet or smartphone.In "Wireless Networks" includes transmitter "wi-fi".
- compiles a list of available networks by scanning.Choosing our and connect to it.Do not forget to enter the previously specified password.
- Then, like launching a browser and type in any address and open the home page of this site.
And what do we have?
As seen from the above stated, not so much and complex configuration of the router DIR-615, and she forces anyone, even a novice.Another distinct advantage of the router - is a high degree of reliability.Therefore, configure this router is performed only once, and then it is possible even to forget.
