question of how to paint light alloy wheels with their hands, not idle, and very relevant.The fact is that every motorist will sooner or later there is a dilemma: to buy new CDs or renovate old ones.Usually it is solved as follows: bought new wheels and the car completely change one's shoes, but the old disks are not thrown away, and repaired.How?Now and analyze.
about how to properly paint alloy wheels
to paint alloy wheels, they need to be prepared.Preparation need to paint is flat and does not peel off during use.If the tires are removed, the repair and painting of disks will not be any problems.If they still put on, it is necessary to paste over them with tape in order not to paint the tires themselves.Repair and painting alloy wheels still better and more reliable comes at the removed tires.
alloy wheels in the operation of different kinds of damage:
• chips;
• detachment;
• abrasions;
• cracks;
• scratch.
How to paint light alloy wheels: repair
In the case of chips and cracks, sadly, wheels need to be repaired, and it means that we will have to refer them to specialists, because at home they are not repaired.
When flaking, scratches and abrasions need to stock up on the following materials and tools:
• spray paint;
• Equipment for painting;
• primer;
• varnish discs;
• sandpaper;
• electric drill with a brush attachment or brush metal;
• solvent or degreaser;
• filler;
• rags;
• wire suspension disk (if necessary);
• hair dryer can be building can be an ordinary home;
• respirator;
• gloves;
• detergents;
• rags;
• kerosene;
• chalk.
Shoe
The first thing you need to start, so it is with the removal of dirt and soot from the disk.This will reveal any defects and send the drive to repair or to start painting.To do this, wearing gloves on his hands, you must using the cloth detergent and brushes for metal drill with a brush attachment to completely clean the disk.
After cleaning before paint alloy wheels with their hands, you must dip them in kerosene or drench using this rag with kerosene.The fact that the liquid can easily penetrate even the smallest crack.After that you need to cover a thick layer of the disc-water Cretaceous solution and allow to dry.
Cracks
If the disk was microcracks, they will appear as black stripes on a white chalk on a disk.These discs are rejected and are not painted, and sent for repairs.Any microcrack grows over time and can lead to accidents.Crack, even the smallest, we need to make.But the matter is complicated by the fact that alloy wheels are always made of light metal (aluminum and magnesium) and brew them simple electrodes does not work, this can be done only with the help of special equipment.
If, however, no defects, the disc is degreased and dried (with a hair dryer can be, can be a natural way).The disk is then trimmed with a brush metal and sandpaper.If necessary, apply a layer of putty for leveling defects.Once dry, apply a coat of primer, and the disc is dried again.Drying can be suspended (by tying it to a rope) or just on any stump).Primers are very different, and therefore drying can take from 20 minutes to one day.Read the instructions for use.
primer may be one, if no dents, no scratches were not.If they were, even when applying coats of filler must be at least 3.
go directly to the cause
Next comes directly painted alloy wheels with their hands.Use the gun to apply the first coat of paint dries and drive.Then, the second and third.But that's not all.The question of how to paint alloy wheels, still not resolved.Without fail they must be covered with a layer of varnish, preferably a colorless (transparent).Then paint sparkle in the sun in all its glory.Luck helps with small cracks, dust and dirt.Lacquered surface repels water, petroleum products, dust, dirt particles from the brake pads, etc.
varnishing process is the same as the paint, but like paint and varnish must be well-ventilated and free of midges and mosquitoes.Otherwise, the insects will stick to fresh paint, and have to repeat the process again.
role
lacquer varnish protects the paint from the external environment, reagents, salt, oil, stones and so on. N. In addition, lacquer protects against bolts that you spin discs.The point of contact is always formed abrasions and even dent.Varnish protects the paint from fading even in the sun.Therefore, do not neglect the lacquer, it is very helpful when operating.Even the dirt does not cling to it.But the buildup of dirt on the wheels negates the balance, and the car begins to "shake" that is not very pleasant for you, and for the machine.
layers of varnish should be applied as long as do not mind.It is recommended that three to five.
So you are almost an expert on the question of how to paint light alloy wheels with their hands.You can, of course, solve the problem in another way: to give them to the studio, even experts are scratching their heads over your problem.If you have enough money, and this is exactly what needs to be done.Otherwise, you can do it on their own.We hope our tips on how to paint the light alloy wheels with their hands, will be useful.We wish you success in this difficult work!
