It often happens that the range of the Wi-Fi sorely lacking.People are strange decisions - buying a more powerful router or a weak accommodation somewhere near the ceiling, but not always, it helps if we are not talking about the Cisco equipment or Zyxel.To solve this problem created by this article, which tells you how to connect the router to the router via a cable, to significantly increase the area of Wi-Fi coverage for your convenience.
Getting Started
to create a network where the wired router is used, it is recommended to use the same device, and it is not only the compatibility of available technologies.Setting up and connecting identical routers is very convenient.Those who wish to save on the purchase, experts recommend purchasing a router and very cheap access point without routing capabilities, as the last task - to relay the signal.
Network "router-router" is available in two versions - for wired and wireless channel.Of course, the connection of the cable is not only more reliable, but also can significantly extend the range of coverage, up to 100 meters.Wireless channel is limited by the power of the signal beams and walls - 10 meters for high-quality signal.Therefore, the organization will need to connect the cable "twisted pair", crimped on both sides of connectors required length.
knowledge are not redundant
Very often even advanced users have a number of problems associated with setting up a network device.The problem - because of inconsistencies between the router manufacturer.Therefore, many IT experts recommend before any adjustment of the equipment to study in detail the operating instructions.Hope for the setup wizard to help make changes to the router, it is not necessary, sometimes not enough information to properly run the equipment in operation.
Before connecting the router TP-LINK or D-Link to a PC or laptop for configuration, we recommend that you submit to them the power and wait for a full load (20-45 seconds), or, as often happens, the equipmentIt may not notice that it is connected to some device in the port of LAN.
Organization of access to the settings
Pursuing the question: "How do I connect the router to the router by cable?" - Many users may be faced with a problem when you connect to your router to make changes to the computer or laptop.Regardless of the operating system or hardware manufacturer, there is only one requirement - to configure the connected devices must be in the same network.Options are only two solutions:
- The factory setting is included with the router has DHCP-server.Ideal for all users, requiring only instruct the computer to receive IP-address automatically.
- But the DHCP server is disabled in some models of routers, make the user to work with his hands and head.This is no big deal, but detailed instructions on how to carry out an authorized entry into the router, can not hurt.
Setting dynamic address computer
In the case of the DHCP server enabled on the router and the inability to enter the access point settings need to give your computer a command to a dynamic network address.To do this on your PC you need to perform the following sequence of actions:
- «Control Panel" - "Center of the main network management."In some systems, this sequence includes the item "Network and Internet".
- «Change adapter settings".
- Press alternate mouse button on the active connection and choose "Properties".
- Find the line containing the characters TCP / IPv4 and then click "Properties."
- Select the check boxes in front of two lines of "Get automatically".Save and exit.
before changing settings in the fifth paragraph is recommended to save the set values in a notebook or take a screen shot - perhaps there are registered settings for the Internet to be restored after two routers are configured.
Setting static computer to connect to the router
router for a home can be disabled Server DHCP.Therefore we have to read the instructions, which comes to the unit and to find IP-address of the router.For example, the address found - 100.333.24.15, and the mask is 255.255.248.0.The user must register in the computer network setup appropriate.A distinction needs to be only in the last digit IP-address, set 16 instead of 15, for example.After completing algorithm of actions described in the previous chapter, make settings manually in the fifth paragraph.
- check the boxes next lines of "use."
- IP-address 100.333.24.16.
- mask 255.255.248.0.
- gateway 100.333.24.15.
- Preferred DNS 100.333.24.15.
- Alternate DNS can be left blank.
- save and exit.
Physical Connection Before you connect the router to the Internet, you need to decide which device is the router, and some - the relay.Network cable connected to a LAN-connector port on the router, and the second connector to the WAN (Internet) repeater.For ease of setup both devices have to stand next to each other, to be included in the electrical network and reset to factory settings, unless the router is configured for a job provider.
Very often administrators from the provider when setting up the router password protect their own installation.There is nothing wrong, as long as the LAN port on the router web fed smoothly, or without a complete reset is necessary.
Related settings
figure out how to connect the router to the router via a cable on a physical level, you need to fine-tune the software part.The router must be enabled in DHCP-server - a setting that automatically assigns a network address to a new device when connected.If a router seamlessly connect a laptop or smartphone, then the server distributing IP-addresses works.Otherwise, you need to go into the setup menu of the router, find and open the tab labeled DHCP and you check the box marked "Enable".After the restart the router settings.
But in any case, the repeater requires no user intervention.You must go to its settings and find the bookmark "Network".Once in the menu WAN, you need to select the connection type "Dynamic IP-address".Then you can start configuring the network Wi-Fi.
Another option with a wired interface
urgency to this option only when the WAN (Internet) router at the entrance to one of the devices in working order.Then a cable connection is made between the LAN-ports of the two routers.The problem with this connection is that the network will be two devices with the same network address that will conflict with each other.Therefore it is necessary to turn off the transponder DHCP-server by going to the menu of the same name of the router.Then, without leaving the settings, you need to find a bookmark LAN and set a static address repeater in the same range in which the router works, but with a difference in the final figures.Many experts recommend at all to change the subnet connections to increase from 250 units to 500, but the router for the house is unlikely to pick up more than ten connections.
Example for configuring routers
In addition, how to connect the router to the router via a cable to the user easier to understand how to configure Ballroom with an example.
settings for the router, which is connected directly to the Internet:
- IP-address 192.168.1.1.
- network mask 255.255.255.0.
- DHCP-server "Enable."
- SSID - Glavnaya.
- Wireless Channel = 12.
- Wireless Security Mode - WPA2.
- Cipher Type AES.
- PSK / EAP -PSK.
settings for the repeater:
- IP-address 192.168.1.254.
- network mask 255.255.255.0.
- DHCP-server is "off".
- SSID - Retranslator.
- Wireless Channel = 1.
- Wireless Security Mode - WPA2.
- Cipher Type AES.
- PSK / EAP - PSK.
These settings are different broadcast channels.This is done to ensure that the access point does not interfere with each other.These settings will be helpful to users who need Internet at various locations organized network, for example in different rooms.In the process of moving the mobile device will automatically switch between routers, and on the Internet is not significantly affected.
TP-LINK to help
But the owners of TP-LINK router is very lucky, because the manufacturer bothered the ultimate consumer and provided all of its unit technology extend coverage called WDS.It remains only to explain how to connect the router TP-LINK to a similar device for Wi-Fi.On the transponder must go to the setup menu "Wireless Mode" and look for the list of proposed options select "Enable WSD».Then you can enter the SSID name of the router or use the "Search" button, if you do not know the exact name of the router.Repeater finds within range of all Wi-Fi devices and provide a full list of the names, MAC-addresses, and type of encryption.Will only select the router and click "Connect."Connecting automatically will transfer the user to configure Wi-Fi, which will be asked to register the name of the access point detection, and set a password and encryption type.
In conclusion
As can be seen from the survey, the network "router-router" is not as simple as it seems at first glance.A lot of options and all kinds of pitfalls that can prepare the networking vendor or service provider.In any case, the organization a wireless network at home or at work should start the task by reading all instructions.An understanding of the material and function devices greatly simplify the setup for any user, and this article only helps determine the type of connection.
cable connection is not necessary to neglect, because this class of data on reliability, durability and compatibility with other equipment is considerably higher than the wireless interface.And the data rate Wi-Fi is still lagging behind the Ethernet.
