How to move a drawing from paper to paper and other surfaces

If you can not draw, but want to learn, you should start with the simple - copy drawings.For a start it can be done using tracing paper.This method is most simple in execution.Now, let's examine more closely how to transfer pattern from paper to paper.

Guide To move a picture, observe the following sequence of actions:

1. Select the image, and laid him tracing, pressure tight draw out all the lines, using black acrylic handle.
2. Now we turn tracing paper and put face to a sheet of paper on which you want to transfer the image.
3. pressed tightly and pass it on with a hot iron.
4. Now remove the tracing paper, and further draws a clear enough line.
5. Image ready.

This method is used for simple images that do not contain a large number of complex parts.Now you know how to transfer the pattern from paper to paper in a simple manner.After trying it, you can start another.

more sophisticated way

to transfer complex patterns can be used to copy the grid.With its help it is possible to reduce or increase the scale of the image.

needed:

• the original pattern;
• transparencies;
• capillary pen;
• paper;
• adhesive tape;
• line;
• pencil.

Guide

To develop this method, follow these steps:

1. original image is put on a transparent film, which depicts the squares of the same size.
2. The same cage put on a clean sheet of paper, if the picture is reproduced in the original.How to move a drawing from paper to paper, when the size of the image you want to change?By increasing the size of the squares do more when reduced, respectively, less.
3. Now all you have to do - is to transfer the image on the cell.
4. When the picture with a pencil is completely transferred, you can start to decorate.

Now you know how to transfer an image from paper to paper.Consider other surfaces.

Body as a basis

Tattoo is a highlight of the exterior, but not everyone dares to put figure on the skin, knowing that this decision of a lifetime.For people who are afraid of such an act, however, want to decorate your body beautiful image, the perfect solution is a temporary tattoo.To learn how to transfer the image from the paper to the skin, it is necessary to examine the following information.The main stage is a clear portrayal of the future contours of the image.

picture can be applied to the body by means of:

• copy paper;
• tracings.

first method

For him, follow these steps:

1. Select Picture, defining the place of its application, skin disinfection.
2. Translation image on a blueprint.To do this, put the paper on the original and gently draw out all its contours.
3. wetting blueprint alcohol and attached to the body.
4. to the contours of well-etched, circle them again in a blueprint, trying to keep it intact.

The second method is based on the use of tracing paper.We need to do the following steps:

1. Draw helium pen drawing itself.
2. Disinfect the skin and smear soap.
3. We put tracing paper and draw out the contours of a sharp object.
4. Now paint the picture.

If you do decide to put a permanent picture on your body, go for this very carefully.The main thing - to choose a good room, get tested for allergic reaction and to check that all intrumenty been disinfected.

How to transfer pattern from paper to glass

For taking images with good food circuits and a roll of film.To transfer the need to purchase a pen - a marker for glass, it fits well and is easily washed off the surface.

Instructions:

1. Take the film.Its size should be slightly larger than the picture itself.The film is attached to the surface, which prevents stray picture.
2. image is placed on the film and circled delicately and carefully.
3. Now the film is transferred to the face gently on a previously prepared surface.Training is degreasing its front side.Make sure that the film is completely stuck to the glass, get rid of wrinkles and bubbles.
4. To better transfer again encircle the contour image by any sharp object.
5. It is time to get rid of polyethylene.This is done very carefully so as not to smear pattern.If somewhere there is an error, now is the time to fix them.
6. Now draw a path.This can be done using acrylic paints and brushes.
7. Once everything has dried, carefully with a cotton swab soaked in liquid, get rid of the traces of the marker.
8. within the image fills in any way.If the technique stained glass, all filled with the contour.
9. After drying for a longer product life, you can bake the image or lacquered.It depends on where the object will be used.

How to transfer pattern from paper to wood

To see your favorite image on a wooden base, you just need to follow the steps below.

To work required:

• pattern printed on a laser printer;
• wooden board;
• acrylic gel medium;
• flat tool for leveling the figure;
• paint and cloth;
• soft paraffin or matt glue;
• 2 brush.

Instructions:

1. Select an image.It should be a pattern that will look beautiful on a wooden base.To give some resemblance to the vintage style it can be treated in special programs.
2. image is printed only on the laser printer, is the main condition.
3. picks smooth wooden base.
4. now causes a uniform layer of gel medium.That he will be transferred image onto the prepared surface.
5. have our picture face to the base.At the instant compounds there are bubbles which possibly need to be smoothed.
6. At present the work is finished, leave it for the night, tomorrow will continue.
7. It is time to remove the paper.To do this, soak and scrub her fingers.Right now, you witness a miracle - when removing the paper shows how the image is still on the tree.
8. Now you can use the paint for wood.Watch out for her number, so that the image is not darkened.
9. Now apply liquid paraffin.If necessary, the last two steps can be repeated after drying the first layer.

other basis for the transfer

Metal - base, are also suitable for such "tricks."For accurate and precise enough to work on it two axial draw lines or mark the corners of the image.Now consider in more detail how to move the drawing from paper to metal.

The most common is the use of carbon paper for this.Since the metal - a very hard material, it is covered with white or light-colored paint.The transfer process is started after the complete drying varnish, which is applied before the start of substantive work.

Guide

This method requires compliance with the following rules:

1. figure very tightly secured on the product.This can be done using soapy water.
2. Many masters for the job using stamping-kanfarnik.With him the image is very precise - almost piece of work, which, however, is very time consuming and requires some preliminary training.
3. Tool take three fingers, resting on the ring, which serves as a kind of spring.Gavel is 2-3 mm from the figure, the light strikes it form the dotted line - draw the main outline of the image.The less detail the image, the denser it breaks.
4. When all the line moved, it is possible to wash off the paint.
5. Image can be varnished.

Now you know how to transfer the pattern from paper to paper, the skin on the glass on wood and metal.Forward - for tools, and good luck in your endeavors!