How smear plastic skis?What athletes have resorted to the lubrication?Required is not only for the purchase of a good slide forward, but also to ski does not slip when you move back.
basic types of lubricants
How lubricated plastic skis?For this purpose special materials which are divided into categories of lubricants and sliding holding.If we talk about ski lubricants slip, they often are based on paraffin with the addition of powdered accelerators.Applied to the surface of the ski such lubricant with a cotton swab or by spraying.After drying lubricant skis need to be polished.
Lubricants may be in liquid or solid consistency.Their use contributes to the acquisition of the additional effect of the surface of the ski sticking that is becoming indispensable in repulsion.
Selection of the optimum lubricant for skis is quite a challenge, because it often depends on the existence of an optimum capacity for maximum smooth sliding.One of the best options today can become a professional lubricant for skis Swix.For optimal performance in professional sport individual lubrication superimposed on each other in a staggered manner.
Tools
If necessary lubrication ski lovers, as opposed to professional athletes, may restrict rather modest set of tools.The main tool for waxing iron stands.As the rest of the tools you can use handy tools that exist in every home.
waxing irons good fit with a smooth surface, no holes in the soles.A prerequisite is the presence of a damp sponge that will not only remove excess grease, but also lower the temperature of the soleplate.
primary processing of sliding surface is recommended to perform using a flux wax that does not contain fluoride with a melting point of 60 to 75 degrees.The temperature of the iron should be the lowest possible.This will gradually melt the grease evenly distributing it on the surface of the ski.Keep the iron on ski better when lubricated wide rear surface.Remove excess grease residues with a scraper or any other convenient means available.
The use of available tools and materials ideally suited to amateur athletes who do not need to be lubricated regularly serrated plastic skis.
Accessories
One of the most desirable accessories, if necessary, waxing is a case that will keep the structure of the sliding surface.On top, a special lubricant for sliding skis are very hard to remove from clothing.
important role in the Lubricant playing surface preparation.It is often used fine sandpaper, with which a sliding surface is treated prior to the acquisition of absolute smoothness.
process lubrication
procedure lubricant sliding surface should begin the imposition of so-called primer in a thin layer of wax.Then superimposed solid holding more pliable outer layer of grease.
Like greased plastic skis?Waxing process is as follows:
- Skiing firmly fixed sliding surface up on a flat horizontal plane.Iron is heated to the minimum temperature, and then at its superimposed sole base lubricant so that it drops uniformly laid down on the surface of the ski.
- liquid, molten grease carefully distributed over the surface of the ski in the same iron.If possible, try to avoid excessive heating of the soleplate and the delay in one place in order to avoid burnout surface of the ski.
- Once the lubrication of sliding skis fully harden, the excess must be carefully removed with a scraper.At the end of a sliding surface is rubbed with a nylon brush.
Secrets proper waxing
There are a few useful tips, the use of which will most effectively lubricate skis.First of all, the lubricant must be applied at room temperature, the pre-clean and dry ski.The solid lubricant should be applied to the sliding surface in several separate, previously solidified layers.
To determine how well greased plastic skis with a notch, you need to check them, moving smoothly through the snow, measured way.If the passage of several kilometers of skiing starts to slip, in which case it is recommended to use lubricants higher melting points.
Understand how to properly lubricate the plastic skis allow tracking of environmental factors.No small importance here are indicators of air temperature, the structure of snow and moisture.On this basis, the purchase of lubricants must be especially careful to get acquainted with the description and instructions for use.
In conclusion
sort out how to lubricate the plastic skis, and getting practical skills you need to pay attention to the need for processing the sliding surface at least once a year, which will keep it in good condition.If you frequently ride in all weather conditions and can carry out the procedure more often.Keep greased skis in a dry place at room temperature.
In the end, do not be lazy to fix, where the behavior of the sliding surface of skis with separate lubricants.Only a serious approach to the process and a careful study of the characteristics of each brand can quickly determine the choice of a truly effective means of waxing.
