In terms of thermal insulation qualities of Bath is quite specific structure.Especially in the steam room is important to respect the optimal temperature conditions, as well as the maintenance of a sufficient level of humidity.Typically, these parameters are calculated individually, but the question of how to make the floors in the bath warm, does not lose its relevance.It would seem enough to implement the design in accordance with the design, construction, and if the plan was carried out by experts, the problems in keeping the heat does not arise.Yet there are cases where in addition to the basic insulation baths owners decide to perform additional heating via underfloor heating.
device gender based insulation
One of the most difficult for warming a concrete floor.Therefore, even at the stage of its formation must take into account some of the subtleties of insulation.To continue to be the opportunity to make their own hands a warm floor in the bath without major alterations, you should rely on the technology of the device warmed ties.The first foundation is poured, and then you can start laying the concrete slab.
further performed waterproofing, which is spread insulation.After that comes a layer of concrete with reinforcing mesh.At this stage the possible laying of floor heating and subsequent finish.Knowing how to make the floors in the bath warm, should help in the choice of the upper decorative flooring, which will also participate in the process of heat transfer.To the solution itself has been the most insulated, should be used as a filler concrete block.Also, it makes sense to lay a special detention center after each layer of concrete.
Materials for insulation
If you plan only additional insulation, it is important not to lose the material.To understand how to make a warm floor in the bath should be familiar with the characteristics of insulators such as foam penopolistrirol and perlite.The most affordable is the foam.In addition, it is easy to process and and lightweight material, the plate of which do not decompose and do not absorb moisture.Laying on the floor panels is done in two layers, with docking places must be sealed with foam or residues of foam.
lightweight perlite because of its features require special security measures during installation.For example, the bath room is better to be completely closed, otherwise the material will spread the wind.These inconveniences compensates for the low thermal conductivity of perlite, which it provides in operation.There is a special recipe of how to make the floors in the bath with warm using perlite.To do this, mix the material with water at a ratio of 2: 1 and added to the cement container.The resulting solution should be laid on the concrete base with a thin layer.To replace traditional mineral wool and bulk insulators suitable polystyrene.During the mounting panel is used, the thickness of which reaches 25 cm, and the spraying material.
floor heating on the stove
to create a solid floor heating system should be used resource stone stove.The basis of the design of the heating will be metal "shirt", which includes a longitudinal pipe, which will be conducted by taps.Compounds provided between the taps and the tubes are closed as a result of the overall system.Set "jacket" over the firebox in the stove itself.The water circulation is implemented by means of a pump or a water exchange which takes place under the influence of the temperature difference.
This model demonstrates the technique of how to make a warm concrete floor in the bath with a water resource.Modern systems for warm flooring operate on a similar principle (of which more will be discussed).An extensive network of pipes integrated into the floor of a bath, warming it in periods of heating.In other words, the metal "shirt" operates on the principle of the boiler to heat the water.For full operation of the system and require buffering capacity, which should be installed outside the furnace and associated with the "face" through metal pipes.
Water Heated floor
for device water floor heating is necessary to purchase a special kit that will include a temperature controller and a set of fittings with the connecting elements.We should also look at the pipes - it can be steel, plastic or a plastic model.To understand how to make radiant floor in the bath, you should initially plan scheme wiring pipes.In addition, the coolant has a value which will circulate in pipes, warming bath floor - in addition to water it may be ethylene glycol, antifreeze or other special solution.
To minimize heat loss, should be put on the pipe insulator.In order to improve the heat transfer and design should be supplemented with aluminum foil.There are two versions of the configuration of pipes under the floor - "snail" and "snake."In the first case, the installation will be difficult, but it will be possible to achieve a more uniform heating.Stacking "snake" is simpler and easier to implement, but is less effective.
electric field in the bath
This system is based on heating cables on the basis of the same water the floor, but instead of pipes used wire mesh laid on the base.The main question is how to make warm floors in the bath with cables so that they are not in contact with water.The only solution would be laying-quality waterproofing.In principle, such a scheme is possible in the bath, as manufacturers often produce recommendations and styling in the bathroom areas.The advantages of such a floor is attributed automatically adjust the temperature and compatibility with any type of final decorative coating.On the downside is the need to create waterproofing and dependence on energy supply, respectively, and the inevitable costs of the power system.
The cover heated floors after installation?
Although insulating quality of the floor in the bath mainly affect the layers under the decorative cover, this part of the "pie" has also contributed in the aesthetic appearance of the steam room, and thermal conductivity.Accordingly, it is necessary to decide how to make the floor heating in the bath so that it does not interfere with the final coating of thermal insulation, but at the same time pleasing appearance.
In terms of thermal conductivity and compatibility with the heating system the best solution would be a ceramic tile, which is laid over the pipes or cables on a special substrate.Also worth considering linoleum and laminate - both versions are able to withstand the temperature and stress, and direct contact with an aqueous medium.But it is necessary to choose the specific model as partly a laminate timber and afraid of water, and linoleum can be dangerous mechanical stress and high temperatures.
Conclusion
No matter what technology is chosen warming baths, should be guided by the requirements of security, ease of use and durability of the materials room.However, it is important to know how to make a warm floor in the bath with the expectation of the possibility of further modernization of the system.The advent of water-resistant synthetic materials, improved technologies and the introduction of automatic heating controls - these and other innovations are being actively implemented in the modern sauna and bath.Over time, you may want to improve the existing floor heating, so it is better to foresee the possibility to perform this ideas with minimal losses.
