clothes appeared in humans for a long time.And to this day many scientists, historians, archaeologists have not determined when the first people began to anything over wear.Each year the requirements for clothing only increases.For modern man has is important not only to cover their body, but also have good things.
professionals create new technologies for the processing of fabrics, stitches, cuts.They were invented oblique Bakey.This is a very convenient way to handle any cuts.Finish obtained accurate, smooth and sometimes interesting.The same option allows you to make an attractive edging to every outfit.
Processing neck bias binding
If you do not need to dress a tight collar or deaf, it can be beautifully crafted cutout.To do this, fit oblique Bakey.Make them simple.We need to take the fabric and draw lengths in widths from 4 to 5 cm. It is important to have them not common thread, and at an angle of 45 degrees.The length of such an inlay is calculated as follows: length cutoff plus 2 cm for the seam.Cloth processing, you can choose the color of the dress, and you can contrast or satin.This will give the dress elegant and original look.
Processing cut
about how to make oblique Bakey, as described above.And now look at how to sew it right.There are several ways.For the first strip is first prepared to fold in half (wrong side inside) and ironed.To make it easier to work on and Stitch it accurately, you need to bend over from the edge of the fabric of 0.5 mm and slightly press it.It will be basting line, on which all need to sew.Then, attach the prepared inlay on the front side of the board to the outlet, and then in small stitches on the line proutyuzhennoy tack.The remaining ends on Bakey then sweep and Stitch car.You need to cut off excess fabric.Now bend itself Bakey on the reverse side of the cut, and then baste with small stitches.It is important to do it closer to trim and fold so that the front side of the seam was right in the Wrong.For beginners, masters give advice: you can do right at the seam Bakey, but not more than 1 mm from the edge.If primetka satisfied, then it should be ironed again, and then Stitch on a typewriter.
Another way
This version is slightly different from that described above.But it allowed such treatment of neck and piping.The first thing Molds cut oblique Bakey from any tissue, their width should be from 2 to 3 cm. The fabric is not positioned along the transverse threads, and at an angle of 45 degrees.This allows you to make a neat finish.Next you need to turn in both ends of five millimeters and lightly ironed.The length of the fabric strips must be equal to the length of the processed and cut 2 cm plus seam.
Processing using a special foot
a cut bias binding sewn with your hands very quickly.This work will require just a couple of minutes.It should be prepared to make a strip of fabric to the outlet from the front of the product and small tack stitches.If necessary cuts at the edges Bakey Sew and cut the excess tissue.
in the garment industry are developing new technologies.This allows not only to facilitate the work, but also improve the quality of products.So there was also a device for the piping.It is installed instead of the legs.With it, the fabric is sewn quickly during operation will not form creases or tucks on the fabric.Such treatment of the neck bias binding is easy and fast.
After piping will baste, Stitch need it.The seam is preferably carried on the planned line.Then, remove the excess yarn and Bakey throw on the wrong side of the slice being processed.Second the folded edge of the need to tack back and try to make both ends of Bakey coincided in one seam.Experienced seamstresses hide the seam directly into the crook of inlay on the front of the product and novice tailors can do so on Bakey.The distance from the edge should be no more than 1 mm.Then you need to Stitch.It is advisable that the machine has foot for piping.It remains only to iron, although a method of treating the neck or other recesses depends on the type of fabric.
Processing cut on products from knitted fabric
knitted fabric itself is very complicated.To make a product out of it, you will need special equipment.If the neck is used for the treatment of bias binding, just need a special foot.Of the long strip of fabric cut out as the processed slice plus 2 cm. The width of the strips should be from 1.5 to 2 cm. If tight knits, then preferably one slice, which will be located on the underside of the fabric treated in the overlock stitch or a zigzag.Another edge slightly ironed.Now we need to tack Bakey shear.
After the work done to check whether all turned out the way it should, and then you can start pritachivaniya by car.Working with knits, we must remember that the fabric itself is very flexible, so it's best to set up the line a little zigzag.Strong pull and stretch the fabric as such is not necessary, as the product will lose form.Then, remove the excess thread and Bakey throw to the wrong side.Neaten slice Now bend is required.You just need to carefully tack it, and preferably directly into the joint.To Stitch smoother, better to be ironed and then Stitch on a typewriter.
Decorative finishing neck
can make oblique Bakey satin.Attire immediately becomes solemn and elegant.As an option - use ready-made tapes to buy that now not be easy.Only when you buy should pay attention to the fact that the product was not of equity threads.Skew satin ribbon is always available.They will fall exactly on the cut.Processing this inlay is very easy.
Processing satin ribbon
to cut trimmed with satin piping, it is better to buy a width of about 2 cm. Sew two ways: open-end and closed.The edges of such a tape does not crumble, so the processing method can be selected as desired.To trimmed product with open edge, do not even need zautyuzhka.The tape can tack immediately at a distance of about 1 mm.Then it should go around the Stitch and cut himself.The second edge of the tape is also not required to bend, it just can tack to the product.In this case, the second joint should be identical to the first.If the level of skill in working with a sewing machine is not high enough, you can make a second seam hiding or use another method of treatment.
simplified version of the processing cut satin ribbon
trimmed with satin ribbon can be cut very quickly.Just need a little effort and do everything carefully.To start the tape folded in half face to the very top and ironed.Then attach one end of the tape to the wrong side of the front of the product, and then baste.Pritachivat is not necessary.Likewise tack the second edge of the tape to the underside of the fabric.Again tack.This is to ensure that there is no decoration on the two lines.Those who can not make a double line, this option will suit perfectly.Only then will stitch on a typewriter at a distance of 1 mm from the edge of the tape.At the end of all the work you need to be ironed.
Application oblique Beek in the design of clothing
Once the designers and engineers did not decorate clothes!Take the same oblique Bakey.They can not only treat the neck, or other cuts, but also draw the bottom of the dress or suit, to emphasize the line of flounces or the whole silhouette.Processing Technology is the same as described above.Bakey may be of the same fabric as the dress or blouse, but you can make them contrast.
With oblique Beek can not only handle all the sections on the product, but also to use them as elements of decoration of clothes.Perform this work is quite able to any skilled worker.The main thing that was at hand sewing machine, needle, scissors, cloth.This treatment will help refresh any dress.You just need to cut out the right oblique Bakey and Sew it properly.When cutting should take into account that the strip is cut or not peppered along the longitudinal threads, and on the bias, that is, at an angle of 45 degrees.All work can be done in different ways, the most important thing - first decide which is better suited for this product.It is necessary to take into account that some of the fabric to sew a dress, and then eventually you can get a beautiful new dress.
