Each mobile device, be it a smartphone or tablet, now has a large touch screen.Can be controlled in such a gadget, of course, only by using such a touch screen.This, in turn, causes pollution perfectly clean the display surface, the occurrence of muddy spots potozhirovyh tracks and so on.And that's not to mention the possibility of contaminating the banal display due to external factors.
only solution that can help us all work with the devices, a protective accessory - film.To learn how to stick the film on the phone and tablet, we're going to tell you in this article.
Why glue film?
In addition to using it protects the screen from dirt, dust and fingerprints, there is also a protection function of the display device from mechanical damage.And it is, believe me, is much more serious.
Indeed, in real life it is impossible to ensure 100 percent ideal environment for using your phone or tablet - always a situation may arise when any object by touching the screen, leave a scratch or abrasion.Obviously, the appearance of the gadget will suffer, not to mention about the performance (and transmission of images).
If you know how to stick a protective film on the phone and do it in a timely manner, to worry about your device is not necessary.You simply remove the old film in the event that it kind of stops you want to apply, and replace it with a new one.Thus, the screen of the smartphone or the tablet will remain unharmed.
Without plenochki obviously get rid of scratches appearing will only be possible after the replacement of the screen.
How the film?
Realizing the benefit of the protective film, you should pay attention to how it is arranged.So, if you take one such film in hand, you will see that it has two tabs.The first can be stated that this is the number one protective layer;second, respectively, "layer №2».
That's right - modern films are marketed three layers.If you present them in the form of a sandwich with two slices of bread and sausage inside the real film that will protect your screen is the same "filling" (sausage).The last layer - the "bread" - will be removed during the installation process.They serve to protect the film itself from damage (both the upper and the lower side).If you want to know how to stick the film on the phone, remember to remove them.
Prepare screen
guarantee that the film will reliably hold during use of the device - it is not only its condition and quality.In fact, an important role is also played by the surface on which the film is adhered.In this case, it refers to the screen of your phone or tablet.
To plenochka kept from the surface of the display you want to remove all unnecessary: dust mote, fingerprints, moisture.If anything remains in the future appearance of the screen of the gadget will be a little spoiled.
Again, if you want to know how to stick the film on the phone "iPhone 3q» (as well as any other model), do not forget to clean the display.This can be done with a soft cloth or a cloth that is lint-free.
Quite simply rub the screen and look at it at an angle to determine whether there was anything in it or not.Ideally, the display surface must appear smooth and even.Then, after gluing the protective layer of the film screen will look fine.
first step
So after cleaning the screen the first thing you need to try on the edge of the film to the edge of the screen.According to the instructions on how to stick the film on the phone "Fly 4403" (and not only him), spacing between it and the edge of the display should be equal to about 0.5 millimeters.
This does not mean you have to arm themselves with a ruler and measure the same distance - no.You just need to "eyeball" estimate that by plenochki remained a small gap.This is normal, because the film is produced in slightly smaller than the screen, so that they went more smoothly.
Once outlined the "beginning" - a line which will glue the film, it is necessary to proceed to its further glueing.This should be done gradually, without haste.However, read about it on.
film is applied to the device
As you know, if you do not know how to stick the film on the phone, start with a clear line, then gradually moving to the opposite edge of the device.As experts, we must act with a narrower side of your gadget.So even glue film "front" will be easier.
Next you need to use the tools for leveling the surface layer of the material is already sticked.In particular, it is a plastic card (though the suit and any scraper).Pressing it to the display surface coated with a film, you can "expel" arose there any air bubbles.Thus, the screen will look nice and neat.
skim
Once you have managed to cover the screen of the device plenochkoj, proceed to the next steps - namely, remove its top protective layer.It is simple: you have to pull the label remaining on the film, on which is written "Layer №2» or "Remove after gluing" (depending on the type of film).Do it slowly and carefully.
If you learned how to stick the protective film on the phone (Gerffins this or any other brand), after the removal of the top plenochki you must remain perfectly smooth coating that protects the display device.Actually, after that you can start using your gadget.
Possible problems
Trouble may arise if you, though, and read how to stick the film on the phone, but did not do everything properly.For example, it concerns the uneven gluing film or air bubbles left on the screen.
In the first case, you can just re-stick your plenochku.It takes a little time, and if you do everything right, he does not spoil an accessory, it can be used again.
Another problem - it's the bubbles that will make your screen ugly.You deal with them in several ways.First we have described previously - equips scraper or a plastic card and a "squeeze" them to the nearest edge of the device.This will help overcome the large bubbles.As for the small, the majority of them, in practice, may go away.So do not worry if you find a couple of those.The main thing - that they are not a consequence of any contact between the glass and mote film.
place where glue film
addition to advice on how to stick the film on the phone (the photo - also visual material), would also like to give advice on the places suitable for gluing.
As noted above, it is necessary to eliminate the possibility of dirt, dust, hair and other objects on the glass apparatus.This means that pokleit film quality in dirty, dusty places not normally get.The same applies to the open space - the wind can spoil everything.
recommend that you choose a room where clean and windless.If we talk about an ordinary apartment, it is best suited for this purpose a bathroom, for example.Because of the high humidity there is less dust.
Go to a room and its glue the film.Hopefully, you will succeed!
