theme of the article - you need to know about replacing SHRUS 2109, which are available in the intricacies of this case.In fact, no big deal, do not even need to drive the car on the pit, all you can do, putting it on reliable support.Perform repair is best, first on one side then on the other.So it will be much more effective, and not have to think what to put in the box instead of a hinge.You know that while you remove both differential CV joints are destroyed.
tool for work
To perform all work to replace SHRUS 2109, you must have at its disposal some tools.That's about it somehow and should talk.Firstly, the desirable metal poles that need to be installed at the other side of the vehicle which carried out repairs.Second, one must have stops that will not allow the car to roll.Third, reliable jack needed.Fourth, it requires some special tools.
most important - it is a good clue to the socket 30. It is desirable, with a sturdy handle.With it, unscrewed the hub nut, which is tightened with a large torque.Also can not do without a stripper rod ends.In some cases, you may need a stripper of spherical.But he needed when the ball fell into disrepair.Of course, a vice, a hammer, a chisel and a set of keys.However, you can begin to prepare for repair.
Preparing for repair
First, lift the car.But before that secure its position with chocks and tear on the hub nut.For this raskontrite it and setting key with a large lever, try to unscrew.Note that on both sides of the thread on different hubs.After the fall through the nut, can be raised towards the car and remove a wheel.
And now the question is, when replacing SHRUS 2109 whether to drain the oil from the box?The answer is simple - you need to!But we can not all be drained, but only two-thirds of the total.The fact that the oil begins to flow when you remove the drive.And if you do not plan to replace it, it is not worth risking and losing costly oil.After that you need to remove the steering nozzle.For this to twist the nut, remove the need to pre pin.Using a stripper, is extruded from a finger knuckle rack.You also need to remove the two bolts that mount the housing is made of ball bearings to the hub.
Removing drive
Now you can remove the drive.Even replacing anther external SHRUS 2109 performed better and faster than when the drive is completely removed.But not only this trick.The fact is that when you change the boot should implement washing hinge and put in a new lubricant.So you will be able to increase its life, unless, of course, will not "kill" drives aggressive driving style.Twisting the nut completely from the hub.You can now carefully remove the outer CV joint from it.
To do this, carefully, trying not to damage the brake pipe, yank the rack holding the disc.The hub should be easy to get to the splines on the drive.That's all, you now need to remove the inner.We take into account the fact that the oil is drained out of the box you have.Therefore, using a small chisel that you put between the frame and hinge, and a hammer, knock SHRUS of PPC.You should not try to lay a crowbar, in this case, save only weak, but a sharp blow.
Which of the parts necessary for replacing
course, a set of CV joints.What to choose production - decide for yourself, but the most important thing - to have all the necessary elements: clamps, grease hinges, locking rings.If you do not complete them, then buy separately, they are not worth very much.It is also sometimes necessary to replace the seals SHRUS VAZ 2109. But only if you're watching the oil leaks in the area of the box.Although, if you look at their life, it is best to carry out when removing drive replacement.So it will be much more effective.
In addition, it is possible that you find fault in some hardpoints and drive.For example, excessive wear of the bearing hub.In this case, it is recommended to replace it.Also, it is possible that you will find and damage the ball joint.And it must be disconnected to remove the drive.Turn ball finger to feel, if he had a seizure.When it comes to traffic jamming, it is necessary to change the ball, otherwise it will soon begin to crackle.
Replacement internal SHRUS
when He shall drive, you can start replacing joints.If you plan to only exchange anther internal SHRUS 2109, the churn from the axle shaft need only the outer joint.But domestic washing and avoiding it the new lubricant is highly desirable.For a complete replacement of internal SHRUS it should knock off axis.Since the hinge you no longer need, you should not feel sorry for him, you can operate the most barbaric ways.
Hold in one hand drive, the second hammer.And causes sudden and severe blows to the inner CV joint kits.In order not to keep the drive in your hand, it can hamstring.So it will be much easier to work with.Then rub the slots on the drive, shoot the old ring and put in its place a new one.But before you install the boot.Then gently stuffing new hinge.Under boot squeeze all grease from the tube, which is attached.Some apply directly to the joint.Don boot and fix its collars.
Replacement external SHRUS
If you plan to only exchange anther external SHRUS 2109, then you need at the last stage just pull it, and the old cut.But if you need to replace the entire joint, then act in the same way as in the last paragraph.Drive clamped firmly in the grip of a hammer and knock down with a constant velocity joints.You should not feel sorry for him, because the new will serve you for many years, if the style of riding you are not very aggressive.
As in the previous paragraph, first well washed with half-axis, wipe it dry, and then mount all of the elements.At first boot, then the ring, constant velocity joints in the stuffing slots.That's all there is left only to squeeze out all the grease under the boot, and put it by tightening the clamps.Note that the screw-type clamps can not be used, they will abut against the hub.
Installation drive
To finish installing the entire drive and suspension assembly of all the parties.First, put the inner CV joint.Falls on the slots, and then apply for a driver a couple of sharp blows.This allows the ring to slip into the previously curled to a minimum diameter.Please note that the grenade should fit snugly inside the box, it is its normal position.But do not forget that a little CV joint moves along the axis of the wheels.
Next, you need to know about replacing SHRUS 2109 - is the installation of the external hinge.To do this, set it in front of the hole in the hub and, slightly pressing on the latter, carefully insert it.To confirm definitively that the pomegranate came to the end, you can apply a few sharp blows on the hub.Just substitute the wooden beam to soften.In the future, the hub is fully seated when you tighten the nut.That's all, now you can collect the side and start the second.
Conclusion
After replacing all the joints do not forget to fill in the box of oil.If you try to pull away, you hear that the box is rotated, but the movement is not transmitted to the wheels, the diagnosis is simple - some inner CV joint is not seated, do not hit the slots.We'll have to figure out some junk, and spend his installation again, following all of the recommendations.Also worth noting is that the replacement of CV joints without removing the actuator 2109 can be carried out, but it will be much harder to accomplish.Spend a lot of time and effort.
